Regulatory scope
- Vessels designed for gases, liquefied gases, dissolved under pressure, for vapors and liquids used for fluids of groups 1 and 2
- Boilers intended to produce hot water, temperature of which is over 110 °C or vapor, excessive pressure of which is over 0,05 MPa as well as direct-fired vessels
- Pipelines designed for gases, vapors and liquids used for fluids of groups 1 and 2
- Equipment elements (assembly units) and components hereto that can withstand pressure
- Valves designed for equipment with fluids of groups 1 and 2
- Indicating and safety devices
- Pressure chambers (except for medical single-seated ones)
- Protecting devices and appliances
- Main pipelines, intra-field and local distribution pipelines intended for transportation of gas, oil and other products except for equipment used at the pressure regulation stations or compressor stations
- Gas distribution and gas consumption networks
- Equipment specially designed to be used in nuclear energy area, equipment operating with radioactive environment
- Vessels operating under pressure (pressure vessels), created by blast inside them in line with the technical process or by combustion in the mode of self-spreading high temperature synthesis
- Equipment specially designed to be used on marine and river ships and other floating crafts and underwater facilities
- Brake equipment of railway rolling stock, motor transport and other means of transport
- Vessels specially designed to be used on aeroplanes and other airborne vehicles
- Military-specific equipment
- Parts of machines, which do not represent individual vessels (pump and turbines casings, cylinders of steam, hydraulic, internal combustion engines, air machines and compressors)
- Medical single-seated pressure chambers
- Equipment with aerosol sprayers
- Casings of high-voltage electrical equipment (switchgear assemblies, distributing devices, transformers and rotating electrical machines)
- Casings and housings of the electric power transmission systems elements (power supply cable products and communication cables) operating under excessive pressure
- Equipment manufactured (produced) of non-metallic flexible (elastic) shell
- Exhaust or intake silencers
- Tanks or siphons for carbonated drinks
- Safety justification
- Technical passport of equipment
- Operating manual (instructions)
- Design documentation
- Strength analysis, capacity analysis for safety devices (if such are available according to the design)
- Process procedures and details of the technical processes (data on the used materials, semi-finished products, component parts, welding materials and of the methods and parameters of welding conditions and heat-treatment, non-destructive methods and results)
- Information on the tests (measurements) performed
- Equipment test reports performed by the manufacturer, by a representative authorized by a manufacturer and (or) by an accredited test laboratory
- Document confirming materials and complementary parts performance (if any)
- Certificates of conformity, declarations of conformity or test reports with regard to the materials, component parts (if any)
- List of standards that were voluntarily used when making (producing) equipment for compliance with TR CU 032/2013 from the list to the regulations (in case the manufacturer used them)
- Documents confirming qualification of specialists and personnel of manufacturer
- Other documents, which directly or indirectly certify conformity of equipment to TR CU 032/2013
Our experts can advise you the values of maximum allowable working pressure (MPa), capacity (m3) or nominal diameter (mm) at which the requirements of TR CU 032/2013 are applied to technical devices specified above.
Exempted equipment
Certification / declaration of conformity as per TR CU 032/2013
Certification shall be carried out with regard to equipment of categories 3 and 4 according to schemes 1c, 7c (for series-produced products), 3c (for batch of products) and 4c (for single item).
Declaring with regard to equipment of categories 1 and 2 as well as equipment of any category, which is finalized using permanent connections on site according to schemes 1d, 3d, 5d (for series-produced products) and 2d, 4d (for batch of products, single item).
Our specialists can advise you the description of the certification and declaring schemes as per TR CU 032/2013.
Requirements for applicants
When certifying the products conformity to the requirements of TR CU 032/2013 in the forms of certification and declaring of conformity the applicants can be as follows:
as per schemes 1c, 7с, 1d, 3d, 5d – manufacturers or representatives authorized by manufacturer
as per schemes 3c, 4c, 2d, 4d – manufacturers, vendors or representatives authorized by manufacturer
Mandatory requirement: applicant (legal entity or individual entrepreneur) must be a resident of the Eurasian Economic Union.
Validity periods for a certificate / declaration of conformity
Set of evidentiary documents
For all questions concerning the provisions of TR CU 032/2013 and the conditions for certifying the products conformity to the requirements of the regulations, please feel free to contact our experts.